No sound from the front audio panel. Connection. Setting up the audio driver. Front soundbar not working How to set up front soundbar in windows 10
Read also
- Please explain why, after reinstalling Windows 7, I have a Realtek sound card, installed sound drivers from the motherboard CD, Realtek manager is installed and there is sound in the operating system. But I connect the headphones to the front panel and there is no sound, before reinstalling the operating system there was sound. Georgy.
- Letter No. 2 Answer this question, I recently reset my BIOS settings to default (default) and now I have Front soundbar not working, online they say you need to install the Realtek manager, but I’ve never had it, so it’s something else, probably in the BIOS settings. Anton.
- Letter No. 3 Why do I have no sound in headphones in Windows 7 when connecting them to the front panel? Realtek sound card. On one of the forums on the Internet, I was advised to go to Playback devices and just turn on the headphones, but I can’t do it, because it says High Definition Audio device Not connected and if you right-click on them, this menu will appear and as you can see, they can be Disabled, not Enabled. I also read on one site that you need to go to Start->Control Panel->Sound - in the tabs Playback or Record, select the correct device and click Default, but that doesn’t help either. Christina.
Front soundbar not working
This article, friends, is suitable for both the Windows 7, Windows 8 and Windows XP operating systems, if there is a difference, I will definitely show you where.The answer to the first question. Let's deal with the front soundbar not working, firstly, in most cases, for it to work, you must have Realtek Manager installed. If you have it installed, then there should be an icon for it on the taskbar,
if it is not there, go to Start - Control Panel- Realtek dispatcher. On Windows 7
if it is missing there too, try to find it in the folder
When you launch Realtek Manager in Windows 7, click the Speakers button, then click on the yellow folder in the upper right corner and a window will appear Connector parameters,
we see a warning If front panel jack detection does not work properly, check this box under Disable front panel jack detection, put a tick on this item and click OK.
After these steps, the front soundbar should work.
In the Windows XP operating system, Realtek Manager looks a little different, but the essence is the same. Left-click on the button with the wrench
and in the window that appears, check the box Disable front panel jack detection and OK,
The front soundbar should work.
We can also press the button Additional settings devices in this window and adjust everything as we need, for example, check the item - . This means that when you connect headphones to the front sound panel, the speakers connected to the motherboard at the back will immediately turn off.
Now I am answering the second letter. It happens, friends, that the drivers for the sound card are installed and sound is present in the system, but the front sound panel does not work, there are usually two reasons for this.
Firstly: your front sound panel works according to the slightly outdated AC"97 standard and the cable coming from it is connected to the connector on the motherboard AAFP analog audio front panel ( designed specifically for connecting front panel audio connectors).
- Note: AC’97 is an already outdated standard audio codec, a veteran, one might say, it was developed by Intel in 1997, it is used in motherboards, as well as cases with a front-panel audio solution. But the sound subsystem built into your motherboard operates according to a newer standard - High Definition Audio or HD Audio. This may cause the front soundbar to not work. Intel High Definition Audio is a relatively new specification for audio codecs, developed by Intel in 2004, characterized by improved digital sound quality, an increased number of channels, and a higher bandwidth compared to AC"97.
Reboot and go into BIOS. Go to Advanced, then Onboard Devices Configuration
and finally the option responsible for the front sound panel Front Panel Type, it can also be called like this:
Front Panel Support Type High Definition Front Panel Audio, Legacy Front Panel Audio, it is in the HD Audio position by default,
move it to position, save the changed settings and exit the BIOS. After rebooting, the front soundbar should work.
Also, if your front panel works in HD Audio, then in the BIOS you need to switch it from position to HD Audio. In any case, experiment.
Friends, if you connect the AC"97 front soundbar to the AAFP connector on the High Definition Audio specification motherboard,
Then everything will work fine for you, only in some cases, when connecting headphones to the front sound panel, in sound speakers the sound will not be muted, even if you disable the item in the Realtek manager settings Mute rear output device when connecting front headphone output device.
All this is due to the fact that front sound panel manufacturers use a simplified wiring diagram for the AC97 front panel cables and outputs.
There are two ways out here, the first is to re-solder (not so easy), the second is to buy a new case, with support for the front HD Audio sound panel, and if you purchase a new computer, check everything with the seller, do not be surprised if, when buying a new system unit in a non-specialized supermarket, You will be faced with complete ignorance of consultants on this issue.
Well, the last thing you need to check if your front sound panel does not work is whether it is connected to the motherboard using a cable; sometimes they simply forget to connect it when assembling the computer, as in this screenshot.
They forgot to connect the AC"97 front sound panel cable to the AAFP analog audio front panel connector on the motherboard.
Well, from the third letter to Christina, we installed a new version of the driver from the official website and configured the front sound panel in the Realtek manager, everything is written in our article How to install a sound driver in detail.
Why doesn't the computer see the headphones?
It is impossible to work on all modern computers without an audio system. Basic notifications of system operation are expressed in the form of sound signals. So, you can use speakers or headphones. However, it is not always convenient to listen to music on speakers if there are people sitting next to you who do not want to listen to your music, or other various sounds made by your computer. In this case, it is appropriate to use headphones.
Today you can find many different models of headphones that have different functionality. In addition, there are not only wired headphones, but also wireless devices. Often users encounter a problem when headphones do not work on the computer. So why doesn't the computer see the headphones? Typically, each computer comes with specific sound card software. Sound card outputs can be on the front panel of the system unit or the rear panel, and when connecting headphones, the sound card software must be set with the appropriate connection parameters (headphones, rear speakers, line output). Almost all headphones on computers have microphones. Using this headset you can talk on Skype, as well as other programs. As a rule, when you connect headphones with microphones to your computer, the latter is reflected on the panel. But many people ask the question: why doesn’t the computer see the microphone on the headphones?
Microphone not working on headphones
The first thing you need to do is visually assess the condition of the headphones. Check cable integrity. If the device does not work on your computer, try checking its functionality on another device. But it's best to use a regular MP3 player. It will definitely not have any installed drivers necessary for the headphones to function properly.
If they do not work on other devices, then it is obvious that something is wrong with them. Some people are able to find the problem in the wire. Here, armed with a soldering iron, insulation and scissors, you can repair the headphones yourself. When the speaker itself does not work, it cannot be accurately repaired. But it’s better to contact specialists so as not to completely break your headphones.
If the computer does not see headphones plugged into the jack, then the reason may be in the jack itself. Most often the problem lies in the sound card. Obviously, headphones and even speakers will not work this way.
The computer does not recognize the device
What to do if the computer does not see the headphones? There are even such trivial situations when the Windows panel simply has minimal sound. However, if everything is in order here, then you need to start checking the drivers. In the “device manager” we find the sound settings and check the status of the drivers. If there are no red exclamation marks next to the installed programs, then everything is in order.
When the computer does not see the microphone from the headphones, then you need to accurately look for the appropriate drivers. Expensive headphone models come with a CD on which the drivers are recorded. If the disk was not present when you purchased it or it was lost, then the software can be found on the Internet. You just need to download them only from official websites to ensure full compliance of the devices.
Some users have a problem with bluetooth headphones. If your computer does not see bluetooth headphones, then obviously there is a problem with the drivers. Changing the player you use to listen to music also helps. Or perhaps the bluetooth module is damaged. When Bluetooth headphones are synchronized with a laptop, Bluetooth is already built into it. On desktop PCs, Bluetooth is an add-on in the form of a small chip, similar to a flash drive. A very common reason for Bluetooth headphones not working is the lack of correct settings. Computer doesn't recognize bluetooth headphones? You shouldn't take them in for repairs. Try the settings again carefully according to the instructions.
Modern Monster Beats headphones, which have a microphone, are equipped with two plugs, as well as a USB connector. If the microphone jack is not connected, the headset will not work. Check the quality of the connection between the plug and the socket. Perhaps the contacts have oxidized or you simply mixed up the plugs. To be on the safe side, there are special connectors on the computer panel for headphones and a microphone separately. There are corresponding notes. Don't confuse them when connecting.
So, when your headphones and computer are checked, but there is no sound from the speakers, you need to contact a specialist. Visually it will not be possible to find a breakdown. Only with the help of special equipment can you determine why the headphones do not work, and perhaps the reason is not in them at all, but in the PC or phone.
How and where to troubleshoot
Practice shows that it is headphones that cause the lack of sound. You only need to purchase headphones that have a warranty period. If you find defects or discrepancies in parameters, you can always return the device to the seller. You exchange non-working headphones for new ones or withdraw funds.
Do not try to repair expensive headphones yourself. Please remember that tampering with the device automatically voids the warranty period. If you are not confident in your own knowledge to help repair your headphones, contact a service center.
Main problems
Often, each of us, when connecting our gadget to our home computer, is faced with the problem that the device does not work normally or does not work at all. It goes without saying that the user has a question about why the computer does not see the headphones. There are a lot of situations that lead to this, ranging from incorrectly installed drivers to damage to the device itself.
Basic faults
In this article we will answer the question of what to do if the computer does not see the headphones. The first thing to start with is to check the functionality of the device itself. To do this, you should connect the headphones to another sound-reproducing device that is known to work normally. It is best to choose a regular MP3 player for this purpose, which has virtually no software, including drivers, that could not work properly.
If your headphones don’t work here either, the problem is with them, and the situation becomes clear. There are only two options here: if the breakdown is in the gadget’s wire, you can try to change it, armed with scissors, electrical tape or tape and another cord taken from some similar device. But if the speaker itself fails, nothing can be done and the headphones need to be replaced.
PC problems
The next reason why the computer does not see headphones plugged into the jack may be that it is broken, because if the sound card on your PC is faulty, the device naturally will not work. To check it, use other headphones or speakers.
Also, if there is no sound from your headphones, check to see if the playback volume in your music player or Windows system is set to minimum. The next step in the troubleshooting chain is to check the drivers. To do this, you should go to the so-called “Device Manager” and make sure that your gadget is displayed normally, without question marks and with the correct name. What is needed for this, right-click on the Computer icon, and click properties, then, going to the item - equipment, select the device manager and see if the personal computer sees yours correctly. If they are displayed incorrectly, you should look for the cause of the problem in the drivers.
Software setup
Usually a disk containing original drivers is supplied with the device. After using it, reinstall the software and check again if there is sound. If there was no disk or it was lost, you should download the driver from the Internet; it is important that you download the software only from the official website. After downloading and installing the drivers, reboot your machine.
If after this the computer does not see bluetooth headphones or regular wired ones, try changing the music player you are using, since today there are dozens of excellent free alternatives. For example, Winamp, Jet Audio, Aimp, etc. If the computer does not see the Bluetooth headphones, the reason should be looked for in the Bluetooth module installed on the machine. When using a laptop, this node is built-in; in desktop computers it is usually presented in the form of a small device attached like a flash drive. In both cases, the modules require the correct installation of drivers for them to work correctly.
For Bluetooth headphones to work correctly on a PC, you need to pair them, for which you need to search for available devices in the Bluetooth control panel and connect the ones found. Next, check again in the task manager to see if the newly added device is displayed correctly. After all the manipulations have been completed, sound reproduction and voice transmission should not cause problems.
Microphone
Most often, the computer does not see the microphone from the headphones if such a device is connected incorrectly. Headphones with a microphone equipped with a wired plug have a different type of connector. An additional ring has been added to it - a contact that is not compatible with the socket of the PC itself, since a personal computer has two sockets for connecting headphones and a microphone separately. To eliminate this inconvenience, there are special adapters, which are tees, one input of which has a four-section structure for connecting headphones with a microphone, and the other two are connected to the corresponding connectors of a personal computer.
The next reason why the computer does not see the microphone on the headphones is, as mentioned above, incorrectly installed device software (drivers), because the microphone in Windows is a separate independent device that requires its own drivers. The situation can be easily resolved by installing the missing driver package.
A front panel with audio and USB ports is an integral part of any modern computer. This is a very convenient thing that allows you to connect removable media, headphones or a microphone without unnecessary movements. However, it is often with the front panel that problems arise, as a result of which the sound stops working and you can no longer use the computer as usual. In this article we will try to understand the possible causes of such malfunctions.
Before you start troubleshooting problems with the front headphone and microphone jacks, you need to make sure that all drivers are installed correctly and the sound is working properly on the back panel of the computer. If there is no sound when you connect headphones to the back of the system unit, then the problem is more global and, therefore, requires a different approach to the solution and a separate conversation. We will devote this article entirely to the front panel.
Why doesn't the sound on the front panel work?
We begin diagnostics by remembering at what point the inputs stopped functioning. For example, if the computer was only recently assembled and you have never used headphones with a microphone, then perhaps during assembly the connectors were incorrectly connected (or not connected at all) to the motherboard, i.e. The front panel is simply not connected properly. If the panel worked properly before, then try to determine the action after which the problems probably began. Perhaps some settings were made in the Control Panel or BIOS. If nothing comes to mind, follow the recommendations below.
Checking the headphone and microphone input connections
This item will be relevant for those cases when the computer was disassembled/assembled and after that the sound on the front panel stopped working. You need to make sure that the panel is really connected - the connector is connected to the correct contacts on the motherboard, and the integrity of the supply wires is not damaged. To connect the front panel, either a solid block of two types – AC’97 and HD Audio, or separate connectors with markings can be used.
The AC'97 format is obsolete and is now rare. At the same time, the HD Audio (High Definition Audio) standard is now used everywhere. On the motherboard, the connector for connecting the front panel HD Audio plug usually has a letter designation, for example, F_Audio.
If you are still not sure where to connect the header, use your motherboard manual. Below we provide the AC’97 and HD Audio pinouts.
Connection diagram of individual connectors to AC’97:
Front Panel Configuration in BIOS
Sometimes it happens that the front panel works according to the old AC’97 standard, but the motherboard provides the new High Definition Audio specification. By the way, both connectors are similar, and the user may not notice this discrepancy. However, no problems should arise when connecting a panel with AC’97 to a motherboard with High Definition Audio. True, in some cases you will have to change the operating mode through the BIOS.
We go into the BIOS by pressing the F2 or DEL key when booting the computer. Next, go to the “Advanced” section and look for the “Onboard Devices Configuration” item. Just below is the “Front Panel Type” parameter (it can also be called High Definition Front Panel Audio or Legacy Front Panel Audio). Switch it from the HD Audio position to the AC97 position. If your front panel uses the HD Audio standard and the BIOS is set to AC97, then switch back.
Some motherboards do not provide the ability to change the operating mode of the front panel, but only allow you to disable or enable the sound controller. The Onboard Audio Function parameter (may have a different name) is responsible for this function, providing only the “Enabled” and “Disabled” values. In such a situation, you do not need to reconfigure anything in the BIOS, and the sound should work without additional manipulations.
Setting up sound devices in the Windows 7/10 Control Panel
If you are one hundred percent sure that the front inputs for headphones and microphone are connected correctly and everything is set correctly in the BIOS, it’s time to move on to the sound settings in the Windows 7/10 environment itself. First of all, go to the Control Panel, and then to the “Sound” section. On the “Playback” and “Record” tabs, make sure that the default devices are installed.
To display all devices, right-click anywhere in the window and check the “Show disconnected devices” and “Show disconnected devices” checkboxes.
On the “Playback” tab, click the same right button on the active device and select “Properties”. In the “General” section, look at the list of connectors - the item “Front panel 3.5 mm connector” should be present.
In the same way, we check the microphone properties on the “Recording” tab.
Front Panel Configuration Using Realtek HD Manager
If all the steps done did not produce results and the front panel for headphones and microphone still does not work, try playing with the Realtek HD settings. If the drivers are installed correctly, this sound configurator must be present on your computer. We launch it using the icon on the taskbar or, if there is none, by following the path Control Panel - Realtek HD Manager.
In the program window, select the “Speakers” section and click on the yellow folder in the upper right corner.
Make sure that the checkbox next to “Disable detection of front panel sockets” is checked; if it is not there, be sure to check it.
Save the settings and check if the sound on the front panel is now working. In most cases the problem should be resolved.
Here in the Realtek HD manager you can make additional device settings. Follow the corresponding link in the upper right corner of the window.
Please explain why, after reinstalling Windows 7, I have a Realtek sound card, installed sound drivers from the motherboard CD, Realtek manager is installed in...
Hello friends! On the front panel of many case models you can see not only USB ports, but also a pair of audio outputs. This arrangement is convenient because you can quickly connect headphones and a microphone, and you don’t have to look for them on the rear panel (which is especially important if the system unit is not located very well).
However, when assembling the system unit, these ports, like everything else, must be connected correctly, otherwise they will not function normally. Contrary to misconception, this is much easier to do than it seems.
Today I will talk about connecting front audio connectors to motherboards made by ASUS, Gigabyte, MSI, Asrock and other popular brands. I would like to immediately clarify that despite the abundance of models, the pinout here is standardized, and unclear points can be clarified in the instructions for the motherboard.
Port on motherboard
Most often it is designated AAFP or Front Audio and is located next to the USB connection ports and SATA interfaces. Most motherboard manufacturers place these components in the lower right corner of the part.
This port consists of 9 long pins into which special connectors can be inserted. Actually, there should be 10 of them, but the pin with serial number 8, located second from the right in the top row, is missing. The connector going to the front panel does not have a hole in this place. 
Although these connectors are similar in size to USB, it is impossible to confuse them due to the different positions of the missing plugs.
When connecting the front panel, you should carefully place the connectors on the pins without deviations left and right, so as not to bend or break them (the latter leads to the fact that it is impossible to use such a port in the future and you will have to be content with the rear audio connectors).
Connectors and their markings
Today, most cases are equipped with a ready-made connector, which is usually labeled AC’97 or HD Audio (depending on the driver used by the motherboard). However, this is not always the case: in some cases, each cable comes separately and is marked accordingly:
- Mic In (Mic Data) + Gnd – paired microphone signal;
- Mic Power – single, microphone power;
- R Out (Ear R) + R Ret – right channel, paired;
- L Out (Ear L) + L Ret – left channel, paired;
- A pair of single Gnd or Ground – grounding.
The pinout is always indicated in the instructions for the motherboard. The connector connection diagram may differ between brands, but most often it is standardized and corresponds to the pinout of the previously mentioned AC’97 or HD Audio plugs.
If the connection is incorrect, nothing bad will happen to your PC, the audio connectors on the front panel will simply not work. Also keep in mind that to use this function on a computer, the motherboard must be equipped with an integrated sound card.
As you can see, there is nothing complicated in connecting the front audio outputs, and if you have already reached this stage when assembling your computer, it will not cause any particular difficulties. I also advise you to read
- Please explain why, after reinstalling Windows 7, I have a Realtek sound card, installed sound drivers from the motherboard CD, Realtek manager is installed and there is sound in the operating system. But I connect the headphones to the front panel and there is no sound, before reinstalling the operating system there was sound. Georgy.
- Letter No. 2 Answer this question, I recently reset my BIOS settings to default (default) and now I have Front soundbar not working, online they say you need to install the Realtek manager, but I’ve never had it, so it’s something else, probably in the BIOS settings. Anton.
- Letter No. 3 Why do I have no sound in headphones in Windows 7 when connecting them to the front panel? Realtek sound card. On one of the forums on the Internet, I was advised to go to Playback devices and just turn on the headphones, but I can’t do it, because it says High Definition Audio device Not connected and if you right-click on them, this menu will appear and as you can see, they can be Disabled, not Enabled. I also read on one site that you need to go to Start->Control Panel->Sound - in the tabs Playback or Record, select the correct device and click Default, but that doesn’t help either. Christina.
Front soundbar not working
This article, friends, is suitable for both the Windows 7, Windows 8 and Windows XP operating systems, if there is a difference, I will definitely show you where.The answer to the first question. Let's deal with the front soundbar not working, firstly, in most cases, for it to work, you must have Realtek Manager installed. If you have it installed, then there should be an icon for it on the taskbar,
if it is not there, go to Start - Control Panel- Realtek dispatcher. On Windows 7
if it is missing there too, try to find it in the folder
When you launch Realtek Manager in Windows 7, click the Speakers button, then click on the yellow folder in the upper right corner and a window will appear Connector parameters,
we see a warning If front panel jack detection does not work properly, check this box under Disable front panel jack detection, put a tick on this item and click OK.
After these steps, the front soundbar should work.
In the Windows XP operating system, Realtek Manager looks a little different, but the essence is the same. Left-click on the button with the wrench
and in the window that appears, check the box Disable front panel jack detection and OK,
The front soundbar should work.
We can also press the button Additional settings devices in this window and adjust everything as we need, for example, check the item - . This means that when you connect headphones to the front sound panel, the speakers connected to the motherboard at the back will immediately turn off.
On Windows 7
Now I am answering the second letter. It happens, friends, that the drivers for the sound card are installed and sound is present in the system, but the front sound panel does not work, there are usually two reasons for this.
Firstly: your front sound panel works according to the slightly outdated AC"97 standard and the cable coming from it is connected to the connector on the motherboard AAFP analog audio front panel ( designed specifically for connecting front panel audio connectors).
- Note: AC’97 is an already outdated standard audio codec, a veteran, one might say, it was developed by Intel in 1997, it is used in motherboards, as well as cases with a front-panel audio solution. But the sound subsystem built into your motherboard operates according to a newer standard - High Definition Audio or HD Audio. This may cause the front soundbar to not work. Intel High Definition Audio is a relatively new specification for audio codecs, developed by Intel in 2004, characterized by improved digital sound quality, an increased number of channels, and a higher bandwidth compared to AC"97.
Reboot and go into BIOS. Go to Advanced, then Onboard Devices Configuration
and finally the option responsible for the front sound panel Front Panel Type, it can also be called like this:
Front Panel Support Type High Definition Front Panel Audio, Legacy Front Panel Audio, it is in the HD Audio position by default,
move it to position, save the changed settings and exit the BIOS. After rebooting, the front soundbar should work.
Also, if your front panel works in HD Audio, then in the BIOS you need to switch it from position to HD Audio. In any case, experiment.
Friends, if you connect the AC"97 front soundbar to the AAFP connector on the High Definition Audio specification motherboard,
Then everything will work fine for you, only in some cases, when connecting headphones to the front sound panel, in sound speakers the sound will not be muted, even if you disable the item in the Realtek manager settings Mute rear output device when connecting front headphone output device.
All this is due to the fact that front sound panel manufacturers use a simplified wiring diagram for the AC97 front panel cables and outputs.
There are two ways out here, the first is to re-solder (not so easy), the second is to buy a new case, with support for the front HD Audio sound panel, and if you purchase a new computer, check everything with the seller, do not be surprised if, when buying a new system unit in a non-specialized supermarket, You will be faced with complete ignorance of consultants on this issue.
Well, the last thing you need to check if your front sound panel does not work is whether it is connected to the motherboard using a cable; sometimes they simply forget to connect it when assembling the computer, as in this screenshot.
They forgot to connect the AC"97 front sound panel cable to the AAFP analog audio front panel connector on the motherboard.
Well, from the third letter to Christina, we installed a new version of the driver from the official website and configured the front sound panel in the Realtek manager, everything is written in our article How to install a sound driver in detail.
- Please explain why, after reinstalling Windows 7, I have a Realtek sound card, installed sound drivers from the motherboard CD, Realtek manager is installed and there is sound in the operating system. But I connect the headphones to the front panel and there is no sound, before reinstalling the operating system there was sound. Georgy.
- Letter No. 2 Answer this question, I recently reset my BIOS settings to default (default) and now I have Front soundbar not working, online they say you need to install the Realtek manager, but I’ve never had it, so it’s something else, probably in the BIOS settings. Anton.
- Letter No. 3 Why do I have no sound in headphones in Windows 7 when connecting them to the front panel? Realtek sound card. On one of the forums on the Internet, I was advised to go to Playback devices and just turn on the headphones, but I can’t do it, because it says High Definition Audio device Not connected and if you right-click on them, this menu will appear and as you can see, they can be Disabled, not Enabled. I also read on one site that you need to go to Start->Control Panel->Sound - in the tabs Playback or Record, select the correct device and click Default, but that doesn’t help either. Christina.
Front soundbar not working
This article, friends, is suitable for both the Windows 7, Windows 8 and Windows XP operating systems, if there is a difference, I will definitely show you where.The answer to the first question. Let's deal with the front soundbar not working, firstly, in most cases, for it to work, you must have Realtek Manager installed. If you have it installed, then there should be an icon for it on the taskbar,
if it is not there, go to Start - Control Panel- Realtek dispatcher. On Windows 7
if it is missing there too, try to find it in the folder
When you launch Realtek Manager in Windows 7, click the Speakers button, then click on the yellow folder in the upper right corner and a window will appear Connector parameters,
we see a warning If front panel jack detection does not work properly, check this box under Disable front panel jack detection, put a tick on this item and click OK.
After these steps, the front soundbar should work.
In the Windows XP operating system, Realtek Manager looks a little different, but the essence is the same. Left-click on the button with the wrench
and in the window that appears, check the box Disable front panel jack detection and OK,
The front soundbar should work.
We can also press the button Additional settings devices in this window and adjust everything as we need, for example, check the item - . This means that when you connect headphones to the front sound panel, the speakers connected to the motherboard at the back will immediately turn off.
On Windows 7
Now I am answering the second letter. It happens, friends, that the drivers for the sound card are installed and sound is present in the system, but the front sound panel does not work, there are usually two reasons for this.
Firstly: your front sound panel works according to the slightly outdated AC"97 standard and the cable coming from it is connected to the connector on the motherboard AAFP analog audio front panel ( designed specifically for connecting front panel audio connectors).
- Note: AC’97 is an already outdated standard audio codec, a veteran, one might say, it was developed by Intel in 1997, it is used in motherboards, as well as cases with a front-panel audio solution. But the sound subsystem built into your motherboard operates according to a newer standard - High Definition Audio or HD Audio. This may cause the front soundbar to not work. Intel High Definition Audio is a relatively new specification for audio codecs, developed by Intel in 2004, characterized by improved digital sound quality, an increased number of channels, and a higher bandwidth compared to AC"97.
Reboot and go into BIOS. Go to Advanced, then Onboard Devices Configuration
and finally the option responsible for the front sound panel Front Panel Type, it can also be called like this:
Front Panel Support Type High Definition Front Panel Audio, Legacy Front Panel Audio, it is in the HD Audio position by default,
move it to position, save the changed settings and exit the BIOS. After rebooting, the front soundbar should work.
Also, if your front panel works in HD Audio, then in the BIOS you need to switch it from position to HD Audio. In any case, experiment.
Friends, if you connect the AC"97 front soundbar to the AAFP connector on the High Definition Audio specification motherboard,
Then everything will work fine for you, only in some cases, when connecting headphones to the front sound panel, in sound speakers the sound will not be muted, even if you disable the item in the Realtek manager settings Mute rear output device when connecting front headphone output device.
All this is due to the fact that front sound panel manufacturers use a simplified wiring diagram for the AC97 front panel cables and outputs.
There are two ways out here, the first is to re-solder (not so easy), the second is to buy a new case, with support for the front HD Audio sound panel, and if you purchase a new computer, check everything with the seller, do not be surprised if, when buying a new system unit in a non-specialized supermarket, You will be faced with complete ignorance of consultants on this issue.
Well, the last thing you need to check if your front sound panel does not work is whether it is connected to the motherboard using a cable; sometimes they simply forget to connect it when assembling the computer, as in this screenshot.
They forgot to connect the AC"97 front sound panel cable to the AAFP analog audio front panel connector on the motherboard.
Well, from the third letter to Christina, we installed a new version of the driver from the official website and configured the front sound panel in the Realtek manager, everything is written in our article How to install a sound driver in detail.
Everyone knows that headphones can be connected not only to a smartphone, but also to a personal computer or laptop. However, it is necessary to know the basic principles of the process. Therefore, in this article we will analyze them, and also consider possible difficulties that may interfere with achieving the goal.
How to turn on headphones through the front panel of the computer
- To begin with, it is advisable to find the instructions that are included with the motherboard upon purchase. In it, on the first pages, you can find a diagram. It is necessary in order to detect a special input - a hole for audio connectors. It is usually located at the bottom, next to the USB.
- Next you need to make sure it is correct. To do this, you can refer to the hint where the names are written. The one you were looking for is called an "audio connector".
- Then you can take the required cable. It should be marked “hd audio”.
ATTENTION. If you have an old PC, you may need another one labeled “AC’97”.
- Then you need to find the same connector, but only directly on the panel itself. Based on the diagram, it can be found at the very bottom on the left side. Of course, the location is sometimes different from others, since the manufacturers are different.
IMPORTANT. Do not confuse the recess with others similar to it. It often happens that users connect the product to USB. It is recommended to pay attention to the markings, as each system has one.
- The part has a specific slot that is closed. This is done specifically to prevent you from connecting it incorrectly. This way, if the cable doesn't fit, you don't have to put in much effort. It is enough to check the correctness of your actions, turn again to the diagram and the equipment itself.
Therefore, after the above manipulations, the sound should be automatically played in the future. However, it is worth going into the settings and carefully studying the parameters.
Why don't headphones work on the front panel of the system unit?
Indeed, it may be that the procedure was not successful. In such a situation, it is advisable to independently identify the causes of the malfunction so that you can then eliminate them. Accordingly, the most common of them are:
- If the PC was recently assembled, then it is possible that the connector was connected incorrectly directly to the motherboard.
- Inappropriate settings in the control panel.
- Sound driver problem.
- You should first double-check the functionality of the headphones. That is, connect them to another device. If there is sound, it's not their fault.
- Make sure the switch is in the right place. It often happens that the volume is at a minimum.
- In addition, you should connect the product to the back panel of the computer, instead of speakers. Most often the connector is green.
Thus, if the problem lies in the hardware, then all that remains is to double-check that all the parts are connected correctly. But it’s still worth checking drivers and settings.